|
Solid Punch - Designed for
installing pins, keys and rivets, and for starting their removal. 5pc.
minimum on non-stocked parts.
| |
|
|
|
|
| Number |
Point |
Hex
Stock |
Taper |
Length |
| 201 |
1/16" |
1/4" |
1" |
4" |
| 202 |
3/32" |
1/4" |
1
1/8" |
4
1/2" |
| 203 |
1/8" |
5/16" |
1
1/2" |
5" |
| 204 |
1/8" |
3/8" |
1
3/4" |
5
1/2" |
| 205 |
5/32" |
3/8" |
1
3/4" |
5
1/2" |
| 207 |
3/16" |
1/2" |
2
1/2" |
7" |
| 208 |
7/32" |
5/8" |
4" |
9" |
| 209 |
1/4" |
1/2" |
2
1/2" |
7" |
| 210 |
5/16" |
1/2" |
2/12" |
7" |
Heavy Duty Punch - When extra length is
needed for installation and removal of pins, keys and rivets. 5pc. minimum
on non-stocked parts.
| |
|
|
|
|
| Number |
Point |
Hex
Stock |
Taper |
Length |
| 220 |
1/4" |
3/4" |
4
1/2" |
12" |
| 221 |
5/6" |
3/4" |
4
1/2" |
16" |
| 225 |
3/8" |
7/8" |
4
1/2" |
14" |
| 226 |
1/2" |
7/8" |
4
1/2" |
18" |
Alignment Punch - The long tapered point is
used in aligning and sizing holes in various metals. 5pc. minimum on
non-stocked parts.
| |
|
|
|
|
| Number |
Point |
Hex
Stock |
Taper |
Length |
| 231 |
1/8" |
3/8" |
3
1/2" |
9" |
| 232 |
5/32" |
1/2" |
4" |
10" |
| 233 |
3/16" |
5/8" |
4
1/2" |
11" |
| 244 |
1/4" |
5/8" |
4
1/2" |
12" |
Pin Punch - Used to drive out straight and
tapered pins and rivets. 5pc. minimum on non-stocked parts.
| |
|
|
|
|
| Number |
Point |
Hex
Stock |
Taper |
Length |
| 301 |
1/16" |
1/4" |
1/2" |
4" |
| 302 |
3/32" |
1/4" |
3/4" |
4
1/2" |
| 303 |
1/8" |
5/16" |
7/8" |
5" |
| 304 |
1/8" |
3/8" |
1
1/4" |
5" |
| 305 |
5/32" |
3/8" |
1
1/4" |
5" |
| 306 |
3/16" |
3/8" |
1
1/4" |
5" |
| 307 |
13/64" |
3/8" |
1" |
5/12" |
| 308 |
3/16" |
1/2" |
2" |
7" |
| 309 |
1/4" |
1/2" |
2" |
7" |
| 312 |
5/16" |
1/2" |
2" |
7" |
| 313 |
3/8" |
5/8" |
2" |
7" |
Long Taper Pin Punch - For removing
pins in hard to reach areas where extra length is needed. 5pc. minimum on
non-stocked parts.
| |
|
|
|
|
| Number |
Point |
Hex
Stock |
Taper |
Length |
| 332 |
1/8" |
3/8" |
2
3/4" |
7
1/2" |
| 333 |
3/16" |
1/2" |
3
/12" |
9" |
| 334 |
1/4" |
1/2" |
3
1/2" |
9" |
| 335 |
5/16" |
1/2" |
3
1/2" |
9" |
| 336 |
3/8" |
5/8" |
3
1/2" |
9" |
| 337 |
1/2" |
5/8" |
3/12" |
9" |
Center Punch - Widely used in metal layout
work to mark lines, holes and pilot drill starting points. 5pc. minimum on
non-stocked parts.
| |
|
|
| Number |
Hex
Stock |
Length |
| 249 |
1/4" |
4" |
| 250 |
5/16" |
4" |
| 251 |
3/8" |
4
1/2" |
| 254 |
1/2" |
5
1/2" |
| 256 |
5/8" |
6" |
Prick Punch - The sharp point is ideal for
scribing and for punching starter holes for screws. 5pc. minimum on
non-stocked parts.
| |
|
|
| Number |
Hex
Stock |
Length |
| 269 |
1/4" |
4" |
| 271 |
3/8" |
4
1/2" |
| 273 |
1/2" |
5
1/2" |
Scratch Awl - The extremely sharp point is
used to scribe or scratch lines in sheet metal. 5pc. minimum on
non-stocked parts.
| |
|
|
| Number |
Hex
Stock |
Length |
| 285 |
3/8" |
6
1/2" |
Riveting Punch - The cupped head is designed
for heading or peening section rivets. 5pc. minimum on non-stocked parts.
| |
|
|
|
| Number |
Cut |
Hex
Stock |
Length |
| 215C |
1/4" |
5/8" |
6" |
Roll Pin Punch - With a hardened point, long
shaft and large striking head, these punches are machined specifically for
removing spring and roll pins. 5pc. minimum on non-stocked parts.
| |
|
|
|
| Number |
Cut |
Hex
Stock |
Length |
| 601 |
1/16" |
1" |
2
3/4" |
| 602 |
5/64" |
1
1/2" |
3
1/4" |
| 603 |
3/32" |
1
1/2" |
3
/12" |
| 604 |
1/8" |
2" |
4" |
| 605 |
5/32" |
2
1/2" |
5" |
| 606 |
3/16" |
2
1/2" |
5" |
| 607 |
7/32" |
3" |
5" |
| 608 |
1/4" |
3
/12" |
5
1/2" |
| 609 |
5/16" |
4" |
6" |
| 610 |
3/8"4" |
4" |
6" |
| 611 |
7/16 |
4" |
6" |
Nail Set - This 3-piece set with precision
ground cupped points and knurled shanks is a must for the do-it-yourselfer.
5pc. minimum
|
|
|
| Number |
Points |
Length |
| 190C |
1/32"
- 2/32" - 3/32" |
5" |
To the top:
|
